The wireless Reolinks are not great. Like, nothing against the camera itself, however, the WiFi antenna must be smaller than the one in my watch. The range is truly abysmal.
Tapo ones are perfectly fine, good quality all around, but it’s important to specify that I have experience with external, solar powered Reolinks and indoor Tapo, so it’s a bit of a different category.
All I can think is “Do you even lift, bro?” and chuckle.
Seconding this. I had a rock solid Ender 3 since 2018 that got a few upgrades (btt 32 bit silent board, geared extruder, abl, couple of printed add ons) but never really needed any maintenance, recently upgraded to a Sovol SV07 Plus (big SV07, mechanically similar to the SV06) and hot damn! It’s a beast. Not only it goes stupid fast, can reach higher temperatures, heats faster… but it’s great out of the box and it prints TPU like nothing. Really, I tested it without changing anything and it worked fine. Downsides are that I got used to Octoprint and it can’t be used here, but Klipper is a decent replacement. Now, the ugly bit about that: it’s running on a really cheap board and an oddly customized os. You don’t notice any of that normally so that’s a plus, HOWEVER if like me you have a Spaghetti Detective/Obico account things change. There’s some copy paste to do via ssh, then the webcam struggles to hit 15 fps and whatever you do DON’T push any update button! Those wrecked everything. Not a fun few hours when I tried to figure out how to fix it.
Anyway the SV06 mentioned by OP is with Marlin rather than Klipper so none of the warnings apply :D
If it’s colored, it’s bad. I have a lovely purple GITD pla that even had a warning about the purple one not being that much glowy, it still surprised me. Very short time, very dim even if charged with a UV light… I like the color so all in all no big deal, but wow. Speaking of the suggestion of using UV reactive filament (light that, by the way, would keep the GITD ones glowing) some colors just look bright even without needing to be special. For example I have a bright green PETG that pops with UV light.
I’ve never had issues with Cura losing my stuff (been using it with an Ender 3 since… 2019 I think) but the backup plugin is connected with your account. It’s a wonderful thing! New computer? Login, restore backup, everything is like you left it.
I do make sure to use it before any update because I have seen the same kind of posts as you have.
I’m going to top that… I thank whatever assistant I’m talking to. After I get the answer. And they’re not listening anymore.
Real or not, it just feels wrong not to thank after I asked for something and received it.
In iOS there’s an option in the app to select a different icon, including the old design. Now, they’ve updated all the others so if you want the old design and for example the purple icon that’s a no go, but…
I like your solution, quite clever! But in my instance I actually want it to turn off once the print is over. I don’t remember the details but I think it’s set up so it will turn off after the hot end has cooled down for a few minutes, it’s controlled by a plug-in for Octoprint.
You do need to know the number, IF you want to maximize the amount of cooling via open window vs AC.
That aside I’m pretty sure this is an “agree to disagree” situation, mostly because it’s clear we have different tastes. A smart home for me has the value of letting me control everything in a single place (always on me), without going around looking for remotes that might need a new battery. Automations are good, but I want to keep control over every little detail.
So you would be fine being a guest in someone’s else house, no control over anything and just let whatever automations are in place do their thing? But all of this in your own home? Temperature is an important value to know, tells if it’s better to turn off the AC/heat and just open the windows at that time, or when it’s the better moment to open them and air the place. Same with air quality, if it gets worse with the windows open it’s better to close them, or if it’s not great inside it might be a good idea to open.
My fan has an app or a pair of buttons on top, no remote.
Right, I see your point and it makes sense. But at the same time consider this: would you still like all the smart stuff if it was completely automated and you had no access to it? It just works, and you can’t make it work a little differently if needed? And I offer an example of something that I can’t imagine how it could be automated… I have a smart fan, power and orientation is dependent on where I am and how hot I feel. Easy enough to change that with the app as needed. Remember this is something I can control but would not want to give control to other people in the house.
On top of that what about sensors? Without the app you can’t see them so for example no quick glance to check the temperature in multiple rooms and outside.
Also while the app is a bit clunky, it sure beats using that one rather than all of the Philips Hue, LIFX, Yeelight, Xiaomi, Tapo, Kasa, Daikin…
The problem with buttons is that they’re expensive (relatively speaking) and ruin the advantages of having everything in a single place like the HA app.
I am not giving access to “everything” to everyone in the house: I already managed to accidentally turn off the 3D printer mid print instead of a light, shouldn’t expect others to be better than me.
Hard to imagine TP-Link not making their products in China, it is a Chinese company XD
But I do agree: usually they make top quality hardware, been my favorite for… a decade at least? I like their Tapo smart plugs and cameras, my router is TP-Link, I have a second router with a mobile connection and that’s Mercusys (another sub brand) and so on.
I’m sticking with Ubiquiti for wireless networking however.
I love Home assistant, but there’s one major thing IMO that’s missing and prevents me from really using it: user accounts. You can make accounts but they’re mostly pointless as they all have access to everything and you can’t restrict things.
Same one I use, also made an enclosure to 3D print and protect it from rain. It’s been going on without issues since 2020 https://www.printables.com/model/169425-xiaomi-aquara-thermometer-outdoor-case
I have a Sovol SV07 Plus, that is the newer version of the SV06 Plus… or in other words, the mechanically identical, but larger, SV06. It’s easy to assemble, it’s bigger than the A1 Mini. Now, you don’t know how big your printer needs to be, until you find out that it’s too small! I found that the 22cm square offered by my old Ender 3 was enough for most things, but it wasn’t enough for everything. I also had a 12cm square with a Monoprice Select Mini Plus V2(the name was the biggest thing lol) and that was quick to become restrictive. Would I suggest the A1 Mini, that has halfway between the two? I don’t know. But at the same time it comes pre assembled (it might not be a concern for you) and easy to use. In short I would recommend the SV07 as that’s the small and less expensive version of what I have, but the SV06 should be mechanically identical so that gives me hope it’ll perform equally well. The downsides are a less than stellar control unit (the hardware inside the touchscreen), a weird as fuck cooling fan that is super loud, and instructions that trick you into believing that the packets of screws are numbered in a meaningful way. Don’t. That said it prints everything with ease, it’s really fast and that fan might be loud, but at the same time works wonders. I love it. Oh! Also. Once I ever so slightly fucked up the Z offset, making it scrape quite thoroughly the build surface: nothing got damaged, build surface included!