_prick /prĭk/ noun
… A small, sharp, local pain, such as that made by a needle or bee sting … A pointed object, such as an ice pick, goad, or thorn. _
Suppose calling men bees is more polite than calling them pricks…
Well, what’s out there?
Blah blah blah.
Says you. You’re also inflating my example and simplifying it, making a strawman out of it. I say differently, and so do all those folk downvoting you.
I’m done with this discourse. You’re determined to stick to your position in the mud, and not worth the effort. Good luck with that.
You’re minimizing, plain and simple, by accentuating the positive aspects and softening the negative. Generally folk minimizing are in support of the thing they claim to be in opposition of.
If that’s not your intent, then you really need to work on your communication skills.
As for being triggered, you’re wrong. I believe you’re projecting. Might the cause be all those down votes your posts are receiving? Sure, they don’t mean much… Other than each vote meaning one person disagrees with you. Some folk can’t handle that well.
“I think that instead of it being the end we will simply learn that fully fascist world is actually quite good for business and nothing will change for vast majority of people. I’m not saying it will be good. It will be worse, just not as bad as you think.”
My understanding of your statement: Fascism is good for business! Sure, it’s bad for some people, but most people won’t even notice it. There’s good things about fascism that you’re not aware of. It’s not all bad!
Triggered? Hardly. I’m not about to let a comment like the above go untouched for the bullshit it is, however.
You need to take a walk down to your local library and read some history books.
You’re the one extolling the virtues of fascism.
Add projection to the list, too. You’re just trolling, now. Good luck with that.
Even for a bootlicker, you seem especially bitter, sarcastic, and downtrodden. Might help to find someone licensed to talk that out. Ain’t healthy keeping it bottled up, and spewing vitriol on Lemmy doesn’t help anyone.
Better than trying to lick my way to the center of a boot while making disingenuous jabs on Lemmy.
Speaking up and calling out fascist behavior. Not spending my money on businesses that promote fascists. Voting. Keeping my long barrel in good condition, may it never need to be used.
Soap, ballot, jury, and cartridge boxes, in that order.
Spoken like a good little bootlicker.
Best keep that tongue on that boot, lest it steps on you instead. Same goes for those businesses under a fascist government. I’m sure life will be good for them, especially if they don’t mind the taste of leather.
Remove their tongue from the boot, and business won’t be good for them.
I’ll do that. Should I be using the “Ender-3 4.2.2 mainboard (32bit)” firmware? I’ve read that the Marlin firmware isn’t compatible with the GD CPUs, so I’m assuming the “Ender-3Marlin2.0.6HW4.2.2GD” won’t work.
Update: support got back to me, with instructions to reflash using the latter firmware. The symptoms changed: during the firmware “upgrade”, the 05 LED flashes about once a second. I let it run for ten minutes, but the printer never rebooted. Powered it off, removed the SD card, powered it back on… Still nothing but a blue display, though the 05 LED keeps blinking once a second.
I’m thinking it’s a bad motherboard. Waiting on support, now.
I’ve got a laptop running Linux on it; connected it up at some point during my time with it. The laptop was able to see the USB to serial adapter, but I didn’t poke at it to see if anything was talking on the other side. I’ll try that today!
Checked for that, too. Both the original panel and the replacement only have one “port” for the cable on the back. The board has spots for two more to be connected, but both are missing. Looking at the front of the panel (as if I’m using it), the port is the left most of the three.
You and I must be listening to different “popular” media then: https://youtu.be/fIIon1S1Das?si=6Em5XMUIGQopoe-j
Just the basic Ender 3, I believe. No version number, so implied v1. Not a Pro, SE, or other appendment to the model.
That’s next on my list, if the replacement panel doesn’t fix the issue. Figured I’d go with the obvious solution first. Doesn’t help that I took a long look at the list of the firmware available for the Ender 3, and figured I’d cross that bridge another day. Creality does not make it simple to identify what’s what.
My guess is yes, on account of me living in the Capital District for two decades and never heard hamburgers referred to as steamed ham. I rarely watch the Simpson’s, so it all makes sense now.