I think you are obligated to share your entire known hosts file to prove this.

Would you mind educating us plebs then? I had a similar question to op, and I can assure you, I definitely don’t understand local auth services the way I probably should.

It might be worth taking a step back and looking at your objective with all of this and why you are doing it in the first place.

If it’s for privacy, then unfortunately that ship has sailed when it comes to email. It’s the digital equivalent of a post card. It’s inherently not private. Nothing you do will make it private. Even services like proton Mail aren’t private–unless you only email other people on proton.

I appreciate wanting to control your own destiny with it but there are much more productive things you could be spending your time on the improve your privacy surface area.

“they are the same picture” -my wife

If it’s working again all of the sudden I would lean towards f2b. I don’t know what your “timeout” is, but if f2b got tripped it would explain why you couldn’t get in yesterday but today it works (assuming your ban expires in 24hrs or so).

GPU with a ton of vran is what you need, BUT

An alternate solution is something like a Mac mini with an m series chip and 16gb of unified memory. The neural cores on apple silicon are actually pretty impressive and since they use unified memory the models would have access to whatever the system has.

I only mention it because a Mac mini might be cheaper than GPU with tons of vram by a couple hundred bucks.

And it will sip power comparatively.

4090 with 24gb of vram is $1900 M2 Mac mini with 24gb is $1000

Like he was saying, it’s more than just power loss. It’s a way of “sanitizing” the power as it comes in. This is “usually” not a problem. But dirty power is arguably worse than power outages. If the voltages fluctuate or get low for whatever reason that puts a big strain on your power supplies.

This could happen because you run a vacuum on the same circuit and your house is old, guy down the street electrocutes himself or the power coming in from the electric company is ‘dirty’ because they have an issue with transformers or up stream somewhere. It can be imperceptible to you, but your tech notices.

Why did you get kicked out?

I switched the the snap package and it’s been rock solid and pain free the entire time.

I welcome any and all comments on why snap is Satan.

This is pretty interesting. I wasn’t aware of the CA stuff ssh added tbh. That might be fine for my needs but I actually like the idea of recording my ssh sessions because I’ve definitely had to go look through a history file to see what I did to set something up.

Seeing exactly what I did and what the terminal output would be pretty huge.

I use vimwiki and wrote a bash script that pulls all of the Todo items from across my wiki and puts them in a single file with TODO and IN PROGRESS sections.

I have a keybind that pulls up the list and runs the script to refresh it.

It’s not linked to any calendar though. I keep my to-do list and calendar separate.

I use Gmail and have that calendar for my personal stuff. At work I am forced to use outlook.

“rocinante” for my proxmox host.

“awkward, past his prime, and engaged in a task beyond his capacities.” From don Quixote’s wiki page.

It seemed fitting considering it is a server built from old PC parts…engaged in tasks beyond its abilities.

The rest of my servers (VMs moslty) are named for what they actually do/which vlan they are on (eg vm15) and aren’t fun or excitin names. But at least I know if I am on that VM it has access to that vlan(or that it’s segregated from my other networks).

I think unRAID does that. But I never looked into it much tbh.

I don’t have nearly that much worth backing up(5TB–and realistically only 2TB is probably critical), but I have a Synology Nas(12TB raid 1) and truenas (zfs striped/mirrored) that I back my stuff to (and they back up to each other).

Then I have a raspberry pi with a USB drive (8tb) at my parents house 4 hours away, that my Synology backs up to (over tailscale).

Oh, and I have a USB HDD(8tb) that I plug in and backup my Synology Nas to and throw in my fireproof safe. But thats a manual backup I do once every quarter or 6 months if I remember. That’s a very very last resort backup.

My offsite is at my parents.

And no, I have not tested it because I don’t know how I’m actually supposed to do that.

So it sounds like Vultr isn’t doing anything nefarious at all.

Someone apparently actually read the terms and services for the first time a few days ago and misunderstood them since they were saying it was in reference to the Vuktr website not your servers.

And either way, they removed the offended lang to clear it up.

This seems like a knee jerk mob reaction more than anything.

There is no evidence that they’ve done anything with anyone’s data.

Idkfa

Yep, that’s exactly what you need. It’s a right of docker passage to not have a volume set up and lose all of your settings/data.

What you are talking about is volumes. You can probably Google a dozen examples but I highly recommend trying chatgpt for questions like that.

It’s pretty good about telling you what you need to do or how to fix a issue with your compose file.

Breaking things is the best way to learn. Accidentally deleting your container data is one of the best ways to learn how to not do that AND learn about proper backups.

Breaking things and then trying to restore from a backup that…doesn’t work. Is a great way to learn about testing backups and/or properly configuring them.

The corrolary to this is: just do stuff. Analysis paralysis is real. You can look up a dozen “right ways” to do things and end up never starting.

My advice: just start. If you end up backing yourself into a corner where you can’t scale or easily migrate to another solution, oh well. You either learn that lesson or figure out a way to migrate. Learning all along the way.

Each failure or screw up is worth a hundred “best practice / how to articles”.

*pro tip

It sounds like you are using a volume and it’s reading the settings you saved. What is the command you ran exactly and I can probably tell you what you need to change or delete to get rid of your old settings.