Tai’shar Malkier!

Good luck with that. .local is reserved for mDNS calls, and not every OS treats it the same way. Ask me how I know.

I bought a cheap used Dell R710 on Facebook marketplace for like $100 or so, as well as an ups, rack, 10g switch, etc, from various other sellers. All told, I’ve got about $500 in my server setup.

Installed proxmox on it. It’s “free” if you don’t buy a license. You just have to put up with a little nag screen when you open the control panel but it still works 100%, much like winrar.

Works great.

Edit: just realized this is in c/selfhosted AND I misunderstood the post. I’m gonna leave it here just on the off chance it’s useful to somebody, but I acknowledge it’s not what you’re looking for.

And I was making a joke about the D&D spider goddess.

But the word is “loath,” which has an accepted alternate spelling of “loth”. “Lolth” is the Dungeons and Dragons spider goddess, commonly worshiped by Drow.

What? This is system programming, not web development.

I simplified a bit. But it’s easy to bork the cable in the process, and it’s also possible the cable didn’t follow standard wire coloring.

Here’s the step by step process for anybody who wants to do this but doesn’t know for sure what to do.

You will need a razor blade or wire stripper and a wire cutter, as well as a roll of electrical tape.

Also it should go without saying, but unplug both ends of the damn cable before you start. And if you’re using a blade, please be careful not to cut your finger open. Paying $800 for stitches in your finger hurts, defeats the purpose of being a cheapass and modding a cable to save a few bucks, and gets blood everywhere.

1. Verify that the usb cable is a CHARGE AND SYNC cable. A charge only cable will not work.

2. With your razor blade, make an incision into the usb cable about 6 inches from either end. Don’t cut too deep. Only go deep enough to cut the outer jacket. The cut should be slightly longer than your tape is wide. If you have a wire stripper, strip about a 3/4 inch section of the cable about 6 inches from either end.

3. If using a blade, cut around the jacket at both ends of your incision and peel off the jacket between your cuts. You should have about 3/4 inch of unwrapped cable.

4. If there’s a wire mesh wrapping the inside of the cable, cut SOME of the mesh, being careful to ensure that the mesh is still connected on both ends. If there’s a foil wrapper, find the seam and peel it back to expose the inner wires. You can cut the foil if necessary, but do not remove it entirely. Ensure that SOME of the foil and/or mesh is still attached at BOTH sides of the exposed section.

5. The inner wires should now be exposed. There should be 4 wires - red black white and green. There might also be a 5th wire with no insulation at all, but this won’t be in all cables. It’s okay if it’s missing. However, if you don’t see ALL of those 4 colors or see different colors STOP. Tape the cable back up and get a different one. If you only see TWO wires, you have a charge only cable and it won’t work. Tape it back up.

6. Clip the red wire TWICE, about an 1/8th inch apart. There should be a gap in the wire now if you line the ends up. DO NOT cut anything else inside the cable. The black white and green wires MUST remain intact for the cable to function.

7. Bend the red wires up and out of the jacket. Close up the foil and/or mesh and wrap ONLY the exposed portion of the cable with ONE layer of electrical tape, leaving the red wires sticking up on either side of the tape. It’s okay if some metal is exposed on either side of the tape, but the red wires should be able to lay down on it without the ends touching anything metal.

8. Lay the ends of the red wires down so that the ends are laying on the tape. The metal inside the red wire should NOT contact anything else that’s metal in the cable.

9. Wrap the whole opened section of the cable with electrical tape to an inch or two on both sides of the open section.

Plug it in and give it a try. You should have data-only usb cable that doesn’t deliver power now. Mark or label the cable in some way so that you don’t lose your mind trying to figure out why this damn usb cable doesn’t charge your phone when you pull it out of a box of random shit 5 years from now.

I bought a X1C and have never leveled it once. Everything is completely automatic, and I’ve never had a failed print.

If I can see that the print quality is starting to go down (and by that I mean I can see a little ringing or something), I just hit the calibrate button and it does everything on its own with zero intervention besides the initial button.

Or just sacrifice a usb cable - carefully open the wire jacket, snip the red wire, then tape it back up. Easy peasy done in 2 minutes.

FWIW, I run proxmox at home, and I friggin love it. It’s really not hard at all.

As a self-hoster thats also a ham…

Fucking ow.

With RAID10, you’d have 8TB of storage that is both striped and mirrored. You’d get a 4x increase in read speed and a 2x increase in write speed. You’d be fault tolerant against AT LEAST one drive failure, possibly two depending on which drives fail.

With RAID5, you’d have 12GB that is striped and parity checked. You’d get a 3x read speed increase and normal write speed. You’d be fault tolerant against a single drive failure.

With RAID6, you’d have 8TB that is striped and parity checked. You’ll have a 2x increase in read speed and normal write speed. You’ll be fault tolerant against two concurrent drive failures.

I recommend RAID10 if you want the all around speed boost and fault tolerance but don’t care so much about capacity;

RAID6 if you care more about redundancy;

RAID5 if you want a read speed boost and more capacity with a little fault tolerance mixed in.

There’s also raid 0, which is gonna be hella fast all around but god help you if somebody farts too aggressively next to it; and raid 1 if you just want 4 redundant backups of the same drive.

Personally, I’d go 10 unless you just really want the extra storage.

Get another hard drive and do RAID5. Then you get striping AND parity.

Or even better, get TWO more drives and do RAID10.

I’ve got 8 SAS drives in a RAID10 and it’s lovely.

I’m paying $115/mo for 1G down 30M up, no data cap.

I WAS paying $150 for the same until I called and bitched that new subscribers were getting the same for $89. So, still getting fucked, but at least they’re using lube now.

There’s fiber literally on the next street over from me. Come the fuck on guys - fiber in my neighborhood. Let’s fucking gooooooooooo already. You’ve been teasing me for years. Quit pulling my hair and fuck me already damn.

I’ve been trying to hunt down cheap used network equipment lately. It’s a weird thing to be disappointed that there aren’t any failing businesses around me :(

I’m about to make an 8 hour round trip drive for a cheap server rack this coming weekend. Please send help.

My last job had a pingpong table. We’d even use it occasionally. That is, until people started getting pissy when they’d see us playing pingpong. Then management started bitching that we were playing pingpong instead of working. Eventually, nobody was allowed to use the pingpong table - it just sat there, in the middle of the room, with brand new paddles and packs of balls that we weren’t allowed to use.

The money was okay - not great, but not terrible. After some management fuckery, I left for a $10000/yr raise and 100% work from home. I’ve gone up $20K since then, been promoted to senior, still have upward trajectory, and still work 100% from home. I have a desk in Memphis somewhere, but I’ve never actually seen it.